 |
Type A-E |
Spirals to right and left joined together by a straight rod. Welded or linked edges.
Max. width: 5,5 m
A: 0,90 a 6 mm / B: 6 a 60 mm / C: 1 a 7 mm / D: 5 a 100 mm
The spiral wire section may also be laminated to achieve a bigger flattened belt. |
|
|
 |
Type A-1 | Spirals to right and left joined together by a crimped rod. Welded or linked edges.
Max. width: 5,5 m
A: 0,90 a 6 mm / B: 6 a 60 mm / C: 1 a 7 mm / D: 5 a 100 mm
The spiral wire section may also be laminated to achieve a bigger flattened belt. |
|
|
 |
Type A-1 | Spirals to right and left joined together by a crimped rod. Welded or linked edges.
Max. width: 5,5 m
A: 0,90 a 6 mm / B: 6 a 60 mm / C: 1 a 7 mm / D: 5 a 100 mm
The spiral wire section may also be laminated to achieve a bigger flattened belt. |
|
|
 |
Type A-2 | Double spiral to right and left joined together by a crimped rod. Welded or linked edges.
Max. width: 5,5 m
A: 0,90 a 6 mm / B: 6 a 60 mm / C: 1 a 7 mm / D: 5 a 100 mm
The spiral wire section may also be laminated to achieve a bigger flattened belt. |
|
|
 |
Type A-3 | Spirals to right and left joined together by a pre-crimped rod. Welded edges. Very flat surface belt.
Max. width: 5,5 m
A: 0,90 a 6 mm / B: 6 a 60 mm / C: 1 a 7 mm / D: 5 a 100 mm
The spiral wire section may also be laminated to achieve a bigger flattened belt. |
|
|
 |
Type B | Groups of spirals in a single direction (right or left) screwed together and assembled in stretches in alternating directions. Linked edges.
Max. width: 4 m
A: 0,90 a 5 mm / B: 10 a 60 mm / solo si alterna / D: 5 a 50 mm
The spiral wire section may also be laminated to achieve a bigger flattened belt. |
|
|
 |
Type B-1 | Groups of spirals in a single direction (right or left) screwed together and assembled in stretches, and with a reinforcing cross rod between each pair of spirals at their contact point; the groups of spirals may be assembled in sections of alternating directions. Linked edges.
Max. width: 4 m
A: 0,90 a 5 mm / B: 5 a 60 mm / C: 1 a 5 mm / D: 5 a 50 mm
The spiral wire section may also be laminated to achieve a bigger flattened belt. |
|
|
 |
Type B-2 | Groups of double spirals in a single direction (right or left) screwed together and assembled in stretches, and with a reinforcing cross rod between each pair of spirals at their contact point; the groups of spirals may be assembled in sections of alternating directions. Welded edges.
Max. width: 4 m
A: 0,90 a 5 mm / B: 10 a 60 mm / C: 1 a 5 mm / D: 5 a 50 mm
The spiral wire section may also be laminated to achieve a bigger flattened belt. |
|
|
 |
Type B-1
with side supports
|
Groups of spirals in a single direction (right or left) screwed together and assembled in streatches, with double spiral at the reinforcing sides, and with a reinforcing cross rod between each pair of spirals at their contact point; the groups of spirals may be assembled in sections of alternating directions. Welded edges.
Max. width: 4 m
A: 0,90 a 5 mm / B: 10 a 60 mm / C: 1 a 5 mm / D: 5 a 50 mm
The spiral wire section may also be laminated to achieve a bigger flattened belt. |
|
|
 |
Type FIL-PLA simple bar |
Belts formed with vertical slides alternately, assembled by means of double cross bars. Linked or welded edges.
Maximum width: 4 m
A: Flattened 12 x 1,20 mm / B: 44,64 mm / C: 4 mm / D: 27,92 mm
To evenly distribute several sprockets across the width of the belt, depending on the specific width. The sprockets must press on the cross rods and not on the laminated metal band. |
|
 |
Type FIL-PLA double bar |
Belts formed with vertical slides alternating plied, assembled by means of double cross bars. Linked or welded edges.
Maximum width: 4 m
A: Flattened 12 x 1,20 mm / B: 44,64 mm / C: 4 mm / D: 27,92 mm
To evenly distribute several sprockets across the width of the belt, depending on the specific width. The sprockets must press on the cross rods and not on the laminated metal band. |
|
|
 |
Type C.A.A. | Spirals to right and left joined together by a straight rod. Sides with chains or honeycomb to assist the even drag ot the belt.
Max. advisable width: 1,20 m
A: 1 a 3 mm / B: 3 a 30 mm / C: 5 a 5 mm / D: 19,05 - 25,4 - 27,77 mm
This type of belt may work in straight conveyors and forming curves. |
|
|
 |
Type MG | Belts consisting of round wire meshes in the direction of travel and hinged to the cross rods which form the union pivots. Edges are welded or linked to side chains.
A: 1,50 a 3 mm / B: 3 a 50 mm / C: 3 a 8 mm / D: 12,70 a 50,80 mm
Width to be advised by customer. |
|
|
 |
Type VAUCANSON-1 | Belts made up of parallel rods in steps, assembled by side loops.
Max. advisable width: 1 m
C: 3 a 6 mm / D: 12,70 a 15,87 - 19,05 a 25,40 - 35 mm
This type of belt is also produced forming curves with different pitches (internal and external). |
|
|
 |
Type VAUCANSON-2 | Belts consist of pitched parellel rods either joined by wire loops at the edges or connected to roller centres of side chains.
Max. advisable width: 2 m
C: 4 a 12 mm / D: 12,70 a 76,2 mm |
|
|
 |
Type A-1 Composed |
Composed of alternating right and left hand spirals joined by crimped cross rods, which are connected to side chains providing positive drive and tracking. These belts may also include angle brackets across the belt width to keep product from sliding on inclines and declines. Opcional edges guards or side plates prevent product from falling off belt edges.
A: 0,90 a 5 mm / B: 3 a 60 mm / C: 4 a 12 mm / D: 12,70 a 76,2 mm |
|
|
 |
Type A Composed |
Spirals to right and left joined together by a straight rod.
These belts may have side plates to prevent the product from falling down, and chains to allow the uniform pulling of the belt. We may also put transversal plates to allow the transport of the product.
Width according to customer's request.
A: 0,90 a 5 mm / B: 3 a 60 mm / C: 4 a 12 mm / D: 12,70 a 76,2 mm |
|
|
 |
Inter-linked wire rods type |
Belts are made with cross wire strands in alternating rectangular shaped and weaved together forming an interlinked flexible belt. This type of belt provides positive traction via pulling sprockets. Usually produced in stainless steel for lightweight transport applications, they are especially useful in food industries.
Max. width: 3 m
Ø Wire dia. C: 1,25 Pitch D: 6,35 / Ø Wire dia. C: 1,80 Pitch D: 12,70 / Ø Wire dia. C: 1,57 Pitch D: 7,40 |
|
|
